Different Types of Threads based on 4 Standards

Here we are going to look at four standards about different types of threads based on 4 standards. (NPT, NPTF, BSPP, and BSPT)

Last updated: August 24, 2020 9:35 am

Editorial Staff

Common

3 Comments

5 Min Read

NPT, NPTF, BSPP, and BSPT

Knowing the thread designation is very important to choose the right connection in threaded joints.

Contents

The two major classifications are based on American ASME/ANSI and British BS standards.

Here we are going to look at four standards about different types of threads.

ASME B1.20.1 – NPT

ASME B1.20.1 is the standard that talks about pipe Threads for general purpose applications.

The most famous and common type of thread in this standard is NPT that is the abbreviation of National Pipe Taper.

National Pipe Taper (NPT)

Some manufacturers use other codes to indicated internal and external threads:

internal and external threads

Note that MPT and FPT are not authorized by ANSI.

NPT(F) as the internal NPT is completely different from NPTF which is the subject of the ANSI B1.20.3.

Design of NPT

The angle between taper and center axis of the pipe is 1° 47’ 24” (1.7800°)
Truncation of roots and crests are flat
60° thread angle

Design of NPT

Commonly used sizes include 1/8, ¼, 3/8, ½, ¾, 1, 1 ¼, 1 ½, and 2 in.

NPT taper pipe threads are intended to be made up wrench-tight and with a sealant (ex. Teflon) whenever a pressure-tight joint is required.

ANSI B1.20.3 – NPTF

ANSI B1.20.3 is another American standard that deals with threads. The difference of the threads in this standard with NPT is that the threads are designed to seal pressure-tight joints without the necessity of using sealing compounds.

Construction

The roots of both the external and internal threads are truncated slightly more than the crests, roots have wider flats than crests so that metal-to-metal contact occurs at the crests and roots coincident with or prior to flank contact.

So, by this method, NPTF eliminates the spiral leakage path.

NPTF

The table below shows the different types of thread presented in ANSI B1.20.3.

Thread Types

Note that NPTF has 2 classes, where a sealant is not used, there is more assurance of a pressure-tight seal for Class 2 threads than for Class 1 threads.

Obviously, to screw NPT to NPTF there is a need for the sealant to avoid leakage.

Beyond American standards, there are ISO ones also, which are totally different.

ISO 228-1 – BSPP

ISO 228-1 is presenting the threads types which do not provide pressure-tight joints. So, they need sealant.

As you see in the figure, the thread angle in ISO 228-1 is 55°. Therefore, it is impossible to screw NPT to BSPP.

Note that for external thread there is 2 tolerance class.

Class A is a finer one. In some documents, they are called Fine and Coarse.

BSPP

Thread Tolerance class

“G” in this designation comes from Gas.

Designation

According to ISO 228-1, the threads are designed like examples in the below table:

ISO 228-1 threads

ISO 7-1 Pressure tight – BSPT & BSPP

The last thread type that we are going to study in this article is the threads that are the subject of ISO 7-1.

ISO 7-1 presents internal and external threads where pressure-tight joints are made on the threads. The thread angle like ISO 228 is 55°.

The taper is 1:16, meaning that for every 16 units of measurement increase in the distance from the end, the diameter increases by 1 unit of measurement.

Tapered and Parallel Threads