Here you find the Top 30 Interview Questions on Pressure Measuring Devices in Pressure Measurement for your exam or job preparation.
The force exerted by the fluid per unit area of the wall of the container is called the absolute pressure.
It is the difference between the absolute and the local atmospheric pressure.
Vacuum pressure is the amount by which atmospheric pressure exceeds the absolute pressure.
The U-tube manometer is the simplest measuring instrument used for gauge pressure measurement by balancing the pressure against the weight of a column of liquid.
Bourdon tube is a device that senses pressure and converts the pressure into displacement. Since the bourdon tube displacement is a function of the applied pressure it may be amplified and indicated by a pointer.
The pressure to be measured is applied to the diaphragm, causing it to deflect. That deflection is being proportional to the applied pressure.
The differential output voltage of the secondary winding of the LVDT is proportional to the displacement experienced by the mass caused due to acceleration on the Core; the differential output voltage becomes a measure of acceleration.
When the strain gauge is stretched or compressed, its resistance changes on the account of the fact that both length and diameter of the strain gauge changes. This change in resistance will be proportional to the torque in the shaft.
The output of a parallel plate capacitor depends on the gap between its movable and fixed plates. Due to pressure, if the gap between the plates is altered, its capacitance also changes. This change in capacitance becomes a measure of pressure.
When a wire is subjected to pressure from all sides its electrical resistance changes. This change in resistance occurs due to the distortion produced in the crystal when subjected to external pressure.
Compression of a sample of the low pressure gas to a level which is sufficiently high so that it can be read with the use of a simple manometer.
When a conductivity wire gets heated electric current flows through it. The rate at which heat is dissipated from this wire depends on the conductivity of the surrounding media.
The hot filament of the hot cathode gauge emits electrons into the vacuum, where they collide with gas molecules to create ions. These positively charged ions are accelerated towards a collector where they create a current in a ion gauge detector circuit. The amount of current is proportional to the gas density.
It is a process of knocking off an electron from an atom and thus producing a free electron and positively charged ion.
When pressure is applied to the bellow element the bellow element will deflect and a displacement will be produced. That displacement will be proportional to the applied pressure.
1. C – type
2. Spiral type
3. Helical type
Bourdon tube is used for pressure measurement.
It is divided into 3 types.
It consists of a oval tube which is made into an arc of 2500. Hence the name C- type. One end of the tube called tip is sealed and it has a link mechanism which moves over a pointer. Other end is attached to a socket where pressure to be measured is applied.
When pressure is applied to bourdon tube, tube will change its position and hence the tip will undergo some displacement and which in turn proportional to pressure applied.
It is made by winding several turns of the tube in the form of spiral. One end is connected to a pointer and other is attached to the socket where pressure can be measured is applied. Here there is no need of geared sector and pinion arrangement.
When pressure is applied to bourdon tube, tube will change its position and hence the tip will undergo some displacement and which in turn proportional to pressure applied
It is made by winding several turns of the tube in the form of helical. One end is connected to a pointer and other is attached to the socket where pressure can be measured is applied. Here there is no need of geared sector and pinion arrangement.
When pressure is applied to bourdon tube, tube will change its position and hence the tip will undergo some displacement and which in turn proportional to pressure applied
Bellows is a series of circular parts resembling the folds .These parts are formed or joined in such a manner that they are expanded or contracted axially by changes in pressure. The metals may be thin enough and they are brass, bronze, copper etc.
Normally bellows has the ability to move over a greater distance than required in a pressure application and therefore to give it maximum life and have better accuracy its movement is generally opposed by a calibrated spring so that only a part of the maximum stroke is used. This system is called spring loaded bellows.
Diaphragms are used to measure pressure. The pressure to be measured is applied to the diaphragm, causing it to deflect; the deflection is proportional to the applied pressure. The movement of the diaphragm depends on its thickness and diameter. The diaphragm element is essentially a flexible disc which may be either flat or corrugated type.
Two different arrangement are used for capsular elements, the convex and nested type
When a wire is subjected to pressure from all sides its electrical resistance changes. This change in resistance occurs due to the distortion produced in the crystal when subjected to external pressure.
A bone ring of about 1 cm dia and 0.5 cm thickness is wound over a insulated manganin wire. The winding is generally bifilar for avoiding inductive effect.
In most common metal wires, the resistance decreases with increase in pressure. While for antimony, bismuth, lithium resistance increases. For cesium it initially decreases for a small values of pressure changes and reaches a minimum beyond which it increases with increase of pressure.
The hot filament of the hot cathode gauge emits electrons into the vacuum where they collide with gas molecules to create ions. These positively charged ions are accelerated towards a collector where they create a current in a conventional ion gauge detector circuit. The amount of current formed is proportional to the gas density.
The grid is maintained at a large positive potential with respect to the cathode and the plate. The plate is at negative potential. Since the positive ion collector is external to the cathode, this method is known as external ionization gauge.
When a potential difference V is impressed across a column of gas with free electrons in the space, the electrons will acquire a kinetic energy Ve. The positive charge on the grid attracts the electrons away from the cathode. They circulate around the grid passing through the fine structures and collide with the grid. The collector inside the grid is negative charged and attracts these positive charged ions.
It measures the total pressure of all the gases present in the system. The pressure of the gas
P = (1/s) Χ (Ip/Ig)
Where s is the sensitivity of the gauge.
In a cold cathode device, electrons are drawn from the electrode surface by a high potential field.
Two sub-types:
VFD simulator download: Master the online tool from the Yaskawa V1000 & programming software for…
The conveyor sorting machine is widely used in the packing industries using the PLC program…
Learn the example of flip-flop PLC program for lamps application using the ladder logic to…
In this article, you will learn the STAR DELTA programming using PLC controller to start…
Lube oil consoles of rotary equipment packages in industrial process plants are usually equipped with…
Rotating equipment packages such as pumps, compressors, turbines need the lube oil consoles for their…