In this article, we are going to discuss the concept of interlocks in boilers.
For the safe operation of boiler and its auxiliaries under higher operating conditions some protection techniques are needed to be followed. These are referred to as interlocks.
Boiler is defined as a closed metallic vessel where the steam is produced by heating water above the atmospheric pressure by the application of heat generated by the combustion of fuelsin the presence of oxygen.
Definition of boilers as per Indian Boiler act (IBR).
According to IBR.
“The boiler is a closed metallic vessel with the design capacity of more than 22.75 liters of water & pressure of above 3.5 kg/cm² is used to generate steam under pressure, with installed mountings to it. And maintaining a pH of Boiler feed water between 8.5 to 9.5.”
An Interlock is a feature that makes two or more machines or devices mutually dependent to each other to prevent the damage of apparatus or devices from undesired conditions. These dependent machines or equipment can be electrical, electronic or mechanical devices.
Generally, Interlocks are considered as start permissive of any equipment that depends on others.
The possibility of preventing the damaging of any machinery equipment or a system. System protection is most necessary to safeguard the machine against undesired damages of machines or equipment. And unusual fluctuation of process parameters to unacceptable value
Generally, interlocks can be categorized as
The primary purpose of interlocks is to protect or safeguard the equipment against abnormal deviation of process parameters to unacceptable values.
Interlocking can be controlled by using suitable sensors and probes to avoid unusual or harmful damage to equipment.
Interlocking units and Reasons for Tripping and measures to avoid tripping of Boiler equipment are shown below
Inter Related Unit: Deaerator
Reason or Cause of Tripping: To avoid low pressure at suction side of BFP.
Minimum Value required to avoid Tripping: The De aerator level must be above 20 % of range and suction pressure must be maintained above 1.5 Kg/cm2.
Reason or Cause of Tripping: To facilitate proper flooding of feed water to feed pumps.
Minimum Value required to avoid Tripping: Differential Pressure must be maintained to 3000 mmwc i.s. 0.3 kg/cm2
Inter-Related Unit: Auxiliary Cooling Water (ACW) Pump.
Reason or Cause of Tripping: To facilitate the pressure of cooling water for proper cooling of mechanical seal and bearings.
Minimum Value required avoiding Tripp: Cooling water pressure must be maintained above 2.5 kg/cm2.
Reason or Cause of Tripping: To avoid ceasing of bearing due to high temperature.
Minimum Value required to avoid Tripping:
Reason or Cause of Tripping: To avoid burning of motor due to high temp.
Minimum Value required for avoiding Tripping: The motor winding temperature must be less than 130 Degrees Celsius.
Inter Related Unit: O2 Analyzer
Reason or Cause of Tripping: To avoid bagasse hipping in a boiler furnace.
Minimum Value required to avoid Tripping: Must be more than 1%.
Inter Related Unit: Drum Feeder
Reason or Cause of Tripping: To avoid chute jamming.
Minimum Value required to avoid Tripping: The drum feeder motor current must be above 13 amps.
Inter Related Unit: Furnace Draft Low i.e. towards negative pressure.
Reason or Cause of Tripping: For furnace safety purposes.
Minimum Value required avoiding Tripping: vacuum should not be less than 150 mmwc.
Inter Related Unit: F.D Fan
Reason or Cause of Tripping: To avoid bearing failures due to high temperature and unbalance of Fan due to high vibration.
Minimum Value required to avoid Tripping:
Inter Related Unit: Furnace draft high i.e. towards positive pressure.
Reason or Cause of Tripping: For furnace safety purposes.
Minimum Value required to avoid Tripping: The vacuum should not be more than 150 mmwc.
Inter Related Unit: Drum level low due to tripping of boiler feed water pump.
Reason or Cause of Tripping: To avoid boiler tube failure.
Minimum Value required avoiding Tripping: Boiler Drum level must be maintained to a minimum of 10% or 15%.
Inter Related Unit: S.A Fan
Reason or Cause of Tripping: To avoid bearing failures due to high temperature and unbalance of the fan due to high vibration.
Minimum Value required to avoid Tripping:
Inter Related Unit: Screw Feeder
Reason or Cause of Tripping: To avoid bagasse carry with flue gas and bagasse distribution properly in the furnace for proper combustion of fuel.
Minimum Value required avoiding Tripping: S.A Fan Pressure but be maintained for a minimum of 250 mmwc.
Reason or Cause of Tripping: To operate damper cylinders for built pressure.
Minimum Value required to avoid Tripping: Compressed air pressure must be a minimum of 3.5 Kg/cm2.
Inter Related Unit: Screw Feeder
Reason or Cause of Tripping: To avoid bagasse failure due to high Temperature and Unbalance of the fan due to high vibration.
Minimum Value required to avoid Tripping:
The safety and process Interlocks employed in the Sugar factory boiler are as follows
Safety Interlocks for Boiler feed Pump I, II, & III.
Process Interlocks for Boiler feed Pump I, II,& III.
DPT – Differential Pressure Transmitter
ZSO – Unit Switch Open Position
Safety Interlock for ID Fan I, & II
Process Interlocks for ID Fan I, & II.
A = I,& II and for ZSC or ZT X =5 & 6 For ID Fan I and II.
Safety Interlock for FD Fan I, & II.
Process Interlocks for FD Fan I, & II.
B = I,& II and for ZSC or ZT X =1 & 2 For FD Fan I and II
Safety Interlock for S.A Fan I, & II.
Process Interlocks for SA Fan I, & II.
C = I,& II and for ZSC or ZT X = 3 & 4 SA Fan I and II
Electrical Drives control the motion of electric motors. Motion control is required in industrial and…
PLC ladder logic design to control 3 motors with toggle switch and explain the program…
VFD simulator download: Master the online tool from the Yaskawa V1000 & programming software for…
The conveyor sorting machine is widely used in the packing industries using the PLC program…
Learn the example of flip-flop PLC program for lamps application using the ladder logic to…
In this article, you will learn the STAR DELTA programming using PLC controller to start…
View Comments
Very nicely illustrated thanks for the sharing