Calibrating Level Transmitter with Remote Seals

How to calibrate the transmitter with a remote seal differential which is implemented in level measurement.Actually, not like where I calibrate the detailed step by step (usually with a HART Communicator), which will be discussed in this post is how to determine the calibration parameters, so that the transmitter works on a range that we want according to the process conditions. But, prior to the calculation method determines the LRV and URV, let us recognize the term first.

There are two terms commonly used in the calibration of the level transmitter with differential transmitter:

Zero Suppression

Zero suppressed required if the transmitter pressure gauge or absolute installed under tapping the side of the high pressure (the bottom side of the process connection). If the transmitter is mounted below the tapping side of the high pressure, the liquid filler (fill fluid) in the capillary puts pressure on the sensor transmitter so as to provide a positive pressure reading even if the tank is empty.

Zero Elevation

Instead, Elevated Zero is required if the pressure gauge or absolute transmitter mounted above the high pressure tapping side (bottom side of the process connection) or on the application of the twoseal differential transmitter (low side and high side). In this case, the transmitter reads a negative pressure when the tank is empty though. This is caused by the effect of head pressure on the fluid filler (fill fluid) on the remote seal capillary tube.

1. Suppressed Zero

Calibrating Transmitter System One Seal with suppressed Zero done if the transmitter is installed below the tapping point the high pressure side as shown below

Calibrating Transmitter System One Seal with suppressed Zero

From the picture above, it is known an open tank level is measured by a level transmitter that uses a single remote seal.

(s f) = specific gravity of the fill fluid (liquid filler in the capillary of remote seal)

(h) = the distance between the process of tapping points to the transmitter.

(s p) = specific gravity of process media that are in the tank.

(H) = The range of levels to be measured.

step 1

Calculate the amount of zero suppression by multiplying the distance between the process connection and the transmitter (h) by gravity liquid filler specifiec remote regret (s f):

Zero Suppression = (h) (s f) = (40 in) (0.93 INH 2 O / in) = 37.2 INH 2 O

Step 2

Calculate the span by multiplying the level range to be measured (H) by the specific gravity of the media that are in the process tanki.specific gravity (s p):

Span = (H) (s p) = (120 in) (1.2 INH 2 O / in) = 144 INH 2 O

Step 3

Determine / calculate calibration for the transmitter, which results in step 1 (zero suppression) as the LRV (Lower Range Value) and results in step 1 plus results in step 2 as the URV (Upper Range Value.

Calibration = “Zero Suppression” until (“Zero Suppression” + “Span”)

= 37.2 INH 2 O to (37.2 + 144) INH 2 O

INH 2 O = 37.2 to 181.2 INH 2 O

Conclusion

So, we calibrate the transmitter with:

LRV = 37.2 INH 2 O

URV = 181.2 INH 2 O

2. Elevated Zero – Open tank

Calibration is performed if the transmitter is mounted above (higher than) the high side tap

single seal elevated zero

Is known:

(s f) = 1.9 in H 2 O / inch

(h) = -30 inches

(s p) = 1.1 in H 2 O / inch

(H) = 120 inches

From the picture above, it is known an open tank level measured her with a transmitter that uses a single remote seal with a transmitter is placed on the high side tapping point.

(s f) = specific gravity of the fill fluid (liquid filler in the capillary of remote seal)

(h) = the distance between the process of tapping points to the transmitter (note the minus sign).

(s p) = specific gravity of process media that are in the tank.

(H) = The range of levels to be measured.

step 1

Calculate the amount of zero elevation by multiplying the distance between the process connection and the transmitter (h) by the specific gravity liquid filler remote regret (s f):

Zero Suppression = (h) (s f) = (-30 in) (1.9 INH 2 O / in) = -57 INH 2 O

Step 2

Calculate the span by multiplying the level range to be measured (H) by the specific gravity of the process media are in the tank, pecific gravity (s p):

Span = (H) (s p) = (120 in) (1.1 INH 2 O / in) = 132 INH 2 O

Step 3

Determine / calculate calibration for the transmitter, which results in step 1 (zero elevation) as the LRV (Lower Range Value) and results in step 1 plus results in step 2 as the URV (Upper Range Value).

Calibration = “Elevation Zero” until (“ZeroElevation” + “Span”)

= -57 INH 2 O to (-57 + 132) INH 2 O

= -57 INH 2 O to 75 INH 2 O

Conclusion

So, we calibrate the transmitter with:

LRV = -57 INH 2 O

URV = 75 INH 2 O

3. Elevated Zero – Closed Tank

This calibration is done if a transmitter with two seal system installed one tapping point level with or above or below the high pressure tap side.

Double seal transmitter with elevated zero

Is known:

(Sf) = 1:07 in H2O / inch

(h) = – 400 inches

(Sp) = 0.9 in H2O / inch

(H) = 350 inches

From the picture above, it is known an open tank level measured her with a transmitter that uses two remote seals each for high and low pressure side of his, the transmitter is placed under the high side tapping point.

(s f) = specific gravity of the fill fluid (liquid filler in the capillary of remote seal)

(h) = the distance between the process of tapping points to the transmitter (note the minus sign).

(s p) = specific gravity of process media that are in the tank.

(H) = The range of levels to be measured.

step 1

Calculate the amount of zero elevation by multiplying the distance between the process connection and the transmitter (h) by gravity liquid filler specifiec remote regret (s f):

Zero Elevation = – (h) (s f) = – (400 in) (1:07 INH 2 O / in) = -428 INH 2 O

Step 2

Calculate the span by multiplying the maximum height of the process fluid (H) by the specific gravity of the process media are in the tank, specific gravity (s p):

Span = (H) (s p) = (350 in) (0.9 INH 2 O / in) = 315 INH 2 O

Step 3

Determine / calculate calibration for the transmitter, which results in step 1 (zero elevation) as the LRV (Lower Range Value) and results in step 1 plus results in step 2 as the URV (Upper Range Value).

Calibration = “Elevation Zero” until (“Elevation Zero” + “Span”)

= -428 INH 2 O until the (-428 + 315) INH 2 O

= -428 To -113 INH INH 2 O 2 O

Conclusion

So, we calibrate the transmitter with:

LRV = -428 INH 2 O

URV = -113 INH 2 O

Also Read: Importance of 4-20mA Current Loop

Don't Miss Our Updates
Be the first to get exclusive content straight to your email.
We promise not to spam you. You can unsubscribe at any time.
Invalid email address

18 thoughts on “Calibrating Level Transmitter with Remote Seals”

  1. Thanks to everyone who involved in this website really sir it’s very owesome & very useful again I want to say many many thanks.

    Reply
  2. dear sir
    In above closed tank u have mentioned there as elevated zero,,,shouldnt be suppresed zero because transmitter is below hp side

    second thing below (3) u mentioned
    **From the picture above,it is known OPEN tank level…….. i think it should be closed instead of open

    am i right?

    Reply
  3. Its really useful. What will be the formulas to calculate LRV and URV if it is direct flanged in HP and LP side is capillary connection.

    Reply
  4. Thank you for the previous reply.. please explain why we include minus sign (-h) in “h” value for elevated zero-open and closed tank calculation.

    Reply
  5. REALLY THANKS A LOT TO THIS BHARDWAJ REDDY.BEACAUSE OF HIM SO MANY PEOPLE GAINING SO MUCH KNOWLEDGE ABOUT INSTRUMENTATION.

    Reply
  6. I have PC INTERFACE 2 , Digital transmitter for level of water tank..so can you help me out how it would be connect to pc and calibrate it?

    Reply

Leave a Comment