Pressure Measurement

Bellows, Diaphragms and Bourdon Tubes

Bellows, Diaphragms and Bourdon Tubes

Mechanical pressure-sensing elements include the bellows, the diaphragm, and the bourdon tube. Each of these devices converts a fluid pressure into a force. If unrestrained, the natural elastic properties of the element will produce a motion proportional to the applied pressure.

Bellows, Diaphragm and Bourdon Tube

Bellows :

Bellows resemble an accordion constructed from metal instead of fabric. Increasing pressure inside a bellows unit causes it to elongate.

Also See : Bellows Working Animation

A photograph of a bellows is shown here:

Diaphragms :

A diaphragm is nothing more than a thin disk of material which bows outward under the influence of a fluid pressure. Many diaphragms are constructed from metal, which gives them spring-like qualities. Some diaphragms are intentionally constructed out of materials with little strength, such that there is negligible spring effect. These are called slack diaphragms, and they are used in conjunction with external mechanisms (e.g. springs) producing the necessary restraining force to prevent damage from applied pressure.

Also See : Diaphragms Working Animation

The following photograph shows the mechanism of a small pressure gauge using a brass diaphragm as the sensing element:

As pressure is applied to the rear of the diaphragm, it distends upward (away from the table on which it rests as shown in the photograph), causing a small shaft to twist in response. This twisting motion is transferred to a lever which pulls on a tiny link chain wrapped around the pointer shaft, causing it to rotate and move the pointer needle around the gauge scale. Both the needle and scale on this gauge mechanism have been removed for easier viewing of diaphragm and mechanism.

Bourdon Tubes

Bourdon tubes are made of spring-like metal alloys bent into a circular shape. Under the influence of internal pressure, a bourdon tube “tries” to straighten out into its original shape before being bent at the time of manufacture.

Most pressure gauges use a bourdon tube as their pressure-sensing element. Most pressure transmitters use a diaphragm as their pressure-sensing element. Bourdon tubes may be made in spiral or helical forms for greater motion (and therefore greater gauge resolution).

Also See : Bourdon Tubes Working Animation

A typical C-shaped bourdon tube pressure gauge mechanism is shown in the following illustration:

A photograph of a C-tube pressure gauge mechanism (taken from the rear of the gauge, behind the pointer and scale) reveals its mechanical workings:

The dark, C-shaped tube is the bourdon tube sensing element, while the shiny metal parts are the linkage, lever, and gear assembly.

Spiral Bourdon Tube

The next photograph shows a spiral bourdon tube, designed to produce a wider range of motion than a C-tube bourdon:

It should be noted that bellows, diaphragms, and bourdon tubes alike may all be used to measure differential and/or absolute pressure in addition to gauge pressure. All that is needed for these other functionalities is to subject the other side of each pressure-sensing element to either another applied pressure (in the case of differential measurement) or to a vacuum chamber (in the case of absolute pressure measurement).

Also see : Pressure Gauge Working Animation

Differential Pressure Sensors

This next set of illustrations shows how bellows, diaphragms, and bourdon tubes may be used as differential pressure-sensing elements:

The challenge in doing this, of course, is how to extract the mechanical motion of the pressure sensing element to an external mechanism (such as a pointer) while maintaining a good pressure seal. In gauge pressure mechanisms, this is no problem because one side of the pressure-sensing element must be exposed to atmospheric pressure anyway, and so that side is always available for mechanical connection.

A differential pressure gauge is shown in the next photograph. The two pressure ports are clearly evident on either side of the gauge:

 Credits : Tony R. Kuphaldt – Creative Commons Attribution 4.0 License

You've successfully subscribed !
Share

Recent Articles

  • PLC Tutorials

Difference Between CompactLogix and ControlLogix

Learn the difference between CompactLogix and ControlLogix PLCs with more I/O's from the Rockwell Automation…

6 days ago
  • PLC Tutorials

Electrical Cabinet Air Conditioner – Enclosure Cooling, Maintenance

Learn the electrical cabinet air conditioner cooling methods and the panel enclosure heat dissipation maintenance.

3 weeks ago
  • Instrumentation Design

Package System Architecture – Control & Instrumentation

The control & instrumentation team in the detail design engineering company provides the package system…

3 days ago
  • PLC Tutorials

Ladder Diagram Example using Memory Bits and Set Coils

In this article, you will learn the PLC ladder diagram example using memory bits and…

1 week ago
  • PLC Tutorials

PLC Project Examples for EcoStruxure Machine Expert

In this article, you will learn the PLC project examples for EcoStruxure Machine Expert software…

1 week ago
  • Common

Preventive Maintenance of Weighing Scale

The weighing scales are found in many industries, almost every plant may have a weigh…

3 weeks ago